Boiler Tube
EN 10216-1 Seamless Steel Tube
EN 10216-1 P195 Seamless steel tubes for pressure purposes,Non-alloy steel tubes with specified room temperature properties.EN 10216-1 P195 for two qualities TR1 and TR2 of seamless tubes.
Standard:EN 10216-1
Seamless steel tubes for pressure purposes – Technical delivery conditions – Part 1: Non-alloy steel tubes with specified room temperature properties
EN 10216-1 Standard specifies the technical delivery conditions for two qualities TR1 and TR2 of seamless tubes of circular cross section with specified room temperature properties made of non-alloy quality steel.
EN 10216-1 P195 Seamless steel tubes for pressure purposes,Non-alloy steel tubes with specified room temperature properties.
Manufacture:Seamless process
Out Dimensions: 14mm-509mm
Wall Thickness: 2mm-50mm
Length: Fixed(6m,9m,12,24m) or normal length(5-12m)
Ends: Plain End, Beveled End, Threaded
Manufacturing process
Steels shall be fully killed.
NOTE This excludes the use of rimming, balanced or semi-killed steel.
The steel name:
(1)the capital letter P for pressure purposes;
(2)the alphanumeric TR1 for qualities without specified aluminium content, impact properties and specific inspection and testing requirements ;
(3)the alphanumeric TR2 for qualities with specified aluminium content, impact properties and specific inspection and testing requirements.
Tube manufacture and delivery conditions
The tubes shall be manufactured by a seamless process. The forming operations and delivery conditions are shown in Table 1.
| Forming operation | Quality | Delivery condition |
| Hot formed | TR1 | As formed or normalized or normalizing-formed |
| TR2 | Normalized or normalizing-formed | |
| Hot formed + cold finished | TR1 and TR2 | Normalized |
Chemical composition of EN 10216-1 P235
| Steel grade | Steel number | C max. | Si max. | Mn max. | P max. | S max. | Cr max. | Mo max | Ni max. | Al tot min. |
| Steel name | Steel number | 0,16 | 0,35 | 1,20 | 0,025 | 0,015 | 0,30 | 0,08 | 0,30 | 0,02 |
| P235TR2 | 1.0255 |
| Cu max | Nb max. | Ti max. | V max. | Cr+Cu+Mo+Ni max. |
| 0,30 | 0,010 | 0,04 | 0,02 | 0,70 |
| Steel grade | Steel number | C max. | Si max. | Mn max. | P max. | S max. | Cr max. | Mo max | Ni max. |
| P235TR1 | 1.0254 | 0,16 | 0,35 | 1,20 | 0,025 | 0,020 | 0,30 | 0,08 | 0,30 |
| Al tot min. | Cu max | Nb max. | Ti max. | V max. | Cr+Cu+Mo+Ni max. |
| – | 0,30 | 0,010 | 0,04 | 0,02 | 0,70 |
Mechanical properties of EN 10216-1 P235
| Steel grade | Tensile properties | Impact properties | ||||||||
| Steel name | Steel number | Upper yield strength R eH b min. for Wall Thickness T mm | Tensile Strength R m | Elongation A min. % b c | Minimum average absorbed energy KV 2 J at a temperature of °C c | |||||
| T ≤ 16 | 16 < T ≤ 40 | 40 < T ≤ 60 | l | t | ||||||
| MPa * | MPa * | MPa * | MPa * | l | t | 0 | -10 | 0 | ||
| P235TR2 | 1.0255 | 235 | 225 | 215 | 320 to 440 | 25 | 23 | 40 | 28 d | 27 |
Note: l = longitudinal t = transverse
Mechanical properties for quality TR1
| Steel grade | Tensile properties | Impact properties | ||||||||
| Steel name | Steel number | Upper yield strength R eH b min. for Wall Thickness T mm | Tensile Strength R m | Elongation A min. % b c | Minimum average absorbed energy KV 2 J at a temperature of °C c | |||||
| T ≤ 16 | 16 < T ≤ 40 | 40 < T ≤ 60 | l | t | ||||||
| MPa * | MPa * | MPa * | MPa * | l | t | 0 | -10 | 0 | ||
| P235TR1 | 1.0254 | 235 | 225 | 215 | 360 to 550 | 25 | 23 | – | – | – |
Note: l = longitudinal t = transverse
Tolerances of EN 10216-1 Seamless steel tubes
Tolerances on outside diameter and on wall thickness
| Outside diameter D mm | Tolerances on D | Tolerances on T for a T/D ratio | |||
| ≤ 0,025 | > 0,025 ≤ 0,050 | > 0,050 ≤ 0,10 | > 0,10 | ||
| D ≤ 219,1 | ± 1% or ± 0,5 mm whichever is the greater | ± 12,5 % or ± 0,4 mm whichever is the greater | |||
| D > 219,1 | ± 20 % | ± 15 % | ± 12,5 % | ± 10 % a | |
| a For outside diameters D ≥ 355,6 mm it is permitted to exceed the upper wall thickness locally by a further 5 % of the wall thickness T | |||||
Tolerances on exact lengths
| Length L | Tolerance on exact length |
| L ≤ 6 000 | + 10 0 |
| 6 000 < L ≤ 12 000 | +15 0 |
| L > 12 000 | +by agreement 0 |
Inspection
Types of inspection
non-specific or specific inspection for quality TR1;
specific inspection for quality TR2.
Testings
(1)Chemical analysis
(2)Tensile test
(3)Impact test
(4)Leak tightness test(Hydrostatic test)
(5)Electromagnetic test
(6)Dimensional inspection
(7)Visual examination
(8)Non-Destructive Testing
Marking
The marking shall be indelibly marked on each tube at least at one end. For tubes with outside diameter D ≤ 51 mm the marking on tubes may be replaced by the marking on a label attached to the bundle or box.
Protection
The tubes will be delivered with a temporary protective coating.
Ordering Information
Mandatory information
(1)the quantity (mass or total length or number);
(2) the term “tube”;
(3) the dimensions (outside diameter D and wall thickness T) ;
(4)steel grade of EN 10216
Options
1) Delivery condition normalized or normalizing-formed for TR1
2) restriction on copper and tin contents
3) product analysis;
4) verification of longitudinal impact testing at −10 °C for quality TR2
5) selection of method for verification of leak-tightness
6) Non-Destructive Testing for quality TR2 ; the test method shall be specified by the purchaser
7) special end preparation ;
8) exact lengths
9) test unit restriction for tubes with D ≤ 76,1 mm of quality TR2
10) wall thickness measurement away from the ends
11) additional marking
EN 10216-1 P235 steel tubes for pressure purposes,Non-alloy steel tubes with specified room temperature properties,EN 10216-1 P235 Seamless steel tubes will be manufactured by a seamless process.
Standard:EN 10216-1
Seamless steel tubes for pressure purposes – Technical delivery conditions – Part 1: Non-alloy steel tubes with specified room temperature properties
EN 10216-1 Standard specifies the technical delivery conditions for two qualities TR1 and TR2 of seamless tubes of circular cross section with specified room temperature properties made of non-alloy quality steel.
EN 10216-1 P235 Seamless steel tubes for pressure purposes,Non-alloy steel tubes with specified room temperature properties.
Manufacture:Seamless process
Out Dimensions: 14mm-509mm
Wall Thickness: 2mm-50mm
Length: Fixed(6m,9m,12,24m) or normal length(5-12m)
Ends: Plain End, Beveled End, Threaded
Manufacturing process
Steels shall be fully killed.
NOTE :This excludes the use of rimming, balanced or semi-killed steel.
The steel name:
(1)the capital letter P for pressure purposes;
(2)the alphanumeric TR1 for qualities without specified aluminium content, impact properties and specific inspection and testing requirements ;
(3)the alphanumeric TR2 for qualities with specified aluminium content, impact properties and specific inspection and testing requirements.
Tube manufacture and delivery conditions
EN 10216-1 P235 Seamless steel tubes will be manufactured by a seamless process. The forming operations and delivery conditions are shown in Table 1.
| Forming operation | Quality | Delivery condition |
| Hot formed | TR1 | As formed or normalized or normalizing-formed |
| TR2 | Normalized or normalizing-formed | |
| Hot formed + cold finished | TR1 and TR2 | Normalized |
Chemical composition of EN 10216-1 P235
| Steel grade | Steel number | C max. | Si max. | Mn max. | P max. | S max. | Cr max. | Mo max |
| P235TR2 | 1.0255 | 0,16 | 0,35 | 1,20 | 0,025 | 0,015 | 0,30 | 0,08 |
| Ni max. | Al tot min. | Cu max | Nb max. | Ti max. | V max. | Cr+Cu+Mo+Ni max. |
| 0,30 | 0,02 d | 0,30 | 0,010 | 0,04 | 0,02 | 0,70 |
| Steel grade | Steel number | C max. | Si max. | Mn max. | P max. | S max. | Cr b max. | Mo b max |
| P235TR1 | 1.0254 | 0,16 | 0,35 | 1,20 | 0,025 | 0,020 | 0,30 | 0,08 |
| Ni max. | Al tot min. | Cu max | Nb max. | Ti max. | V max. | Cr+Cu+Mo+Ni max. |
| 0,30 | – | 0,30 | 0,010 | 0,04 | 0,02 | 0,70 |
Mechanical properties of EN 10216-1 P235
Mechanical properties for quality TR2
| Steel grade | Tensile properties | Impact properties | ||||||||
| Steel name | Steel number | Upper yield strength R eH b min. for Wall Thickness T mm | Tensile Strength R m | Elongation A min. % b c | Minimum average absorbed energy KV 2 J at a temperature of °C c | |||||
| T ≤ 16 | 16 < T ≤ 40 | 40 < T ≤ 60 | l | t | ||||||
| MPa * | MPa * | MPa * | MPa * | l | t | 0 | -10 | 0 | ||
| P235TR2 | 1.0255 | 235 | 225 | 215 | 320 to 440 | 25 | 23 | 40 | 28 d | 27 |
Note: l = longitudinal t = transverse
Mechanical properties for quality TR1
| Steel grade | Tensile properties | Impact properties | ||||||||
| Steel name | Steel number | Upper yield strength R eH b min. for Wall Thickness T mm | Tensile Strength R m | Elongation A min. % b c | Minimum average absorbed energy KV 2 J at a temperature of °C c | |||||
| T ≤ 16 | 16 < T ≤ 40 | 40 < T ≤ 60 | l | t | ||||||
| MPa * | MPa * | MPa * | MPa * | l | t | 0 | -10 | 0 | ||
| P235TR1 | 1.0254 | 235 | 225 | 215 | 360 to 550 | 25 | 23 | – | – | – |
Note: l = longitudinal t = transverse
Tolerances of EN 10216-1 Seamless steel tubes
Tolerances on outside diameter and on wall thickness
| Outside diameter D mm | Tolerances on D | Tolerances on T for a T/D ratio | |||
| ≤ 0,025 | > 0,025 ≤ 0,050 | > 0,050 ≤ 0,10 | > 0,10 | ||
| D ≤ 219,1 | ± 1% or ± 0,5 mm whichever is the greater | ± 12,5 % or ± 0,4 mm whichever is the greater | |||
| D > 219,1 | ± 20 % | ± 15 % | ± 12,5 % | ± 10 % a | |
| a For outside diameters D ≥ 355,6 mm it is permitted to exceed the upper wall thickness locally by a further 5 % of the wall thickness T | |||||
Tolerances on exact lengths
| Length L | Tolerance on exact length |
| L ≤ 6 000 | + 10 0 |
| 6 000 < L ≤ 12 000 | +15 0 |
| L > 12 000 | +by agreement 0 |
Inspection
Types of inspection
non-specific or specific inspection for quality TR1;
specific inspection for quality TR2.
Testings
(1)Chemical analysis
(2)Tensile test
(3)Impact test
(4)Leak tightness test(Hydrostatic test)
(5)Electromagnetic test
(6)Dimensional inspection
(7)Visual examination
(8)Non-Destructive Testing
Marking
The marking shall be indelibly marked on each tube at least at one end. For tubes with outside diameter D ≤ 51 mm the marking on tubes may be replaced by the marking on a label attached to the bundle or box.
Protection
The tubes will be delivered with a temporary protective coating.
EN 10216-1 P265 Tubes for two qualities TR1 and TR2 of seamless tubes of circular cross section with specified room temperature properties made of non-alloy quality steel.
Standard:EN 10216-1
Seamless steel tubes for pressure purposes – Technical delivery conditions – Part 1: Non-alloy steel tubes with specified room temperature properties
EN 10216-1 Standard specifies the technical delivery conditions for two qualities TR1 and TR2 of seamless tubes of circular cross section with specified room temperature properties made of non-alloy quality steel.
EN 10216-1 P265 Seamless steel tubes for pressure purposes,Non-alloy steel tubes with specified room temperature properties
Manufacture:Seamless process
Out Dimensions: 14mm-509mm
Wall Thickness: 2mm-50mm
Length: Fixed(6m,9m,12,24m) or normal length(5-12m)
Ends: Plain End, Beveled End, Threaded
Manufacturing process
Steels shall be fully killed.
NOTE :This excludes the use of rimming, balanced or semi-killed steel.
The steel name:
(1)the capital letter P for pressure purposes;
(2)the alphanumeric TR1 for qualities without specified aluminium content, impact properties and specific inspection and testing requirements ;
(3)the alphanumeric TR2 for qualities with specified aluminium content, impact properties and specific inspection and testing requirements.
Tube manufacture and delivery conditions
EN 10216-1 P265 Seamless steel tubes will be manufactured by a seamless process. The forming operations and delivery conditions are shown in Table 1.
| Forming operation | Quality | Delivery condition |
| Hot formed | TR1 | As formed or normalized or normalizing-formed |
| TR2 | Normalized or normalizing-formed | |
| Hot formed + cold finished | TR1 and TR2 | Normalized |
Chemical composition of EN 10216-1 P265
Chemical composition (cast analysis) a in % by mass for quality TR2
| Steel grade | Steel number | C max. | Si max. | Mn max. | P max. | S max. | Cr max. | Mo max | Ni max. |
| P265TR2 | 1.0259 | 0,20 | 0,40 | 1,40 | 0,025 | 0,015 | 0,30 | 0,08 | 0,30 |
| Al tot min. | Cu max | Nb max. | Ti max. | V max. | Cr+Cu+Mo+Ni max. |
| 0,02 | 0,30 | 0,010 | 0,04 | 0,02 | 0,70 |
Chemical composition (cast analysis) a in % by mass for quality TR1
| Steel grade | Steel number | C max. | Si max. | Mn max. | P max. | S max. | Cr max. | Mo max | Ni max. | Al tot min. |
| P265TR1 | 1.0258 | 0,20 | 0,40 | 1,40 | 0,025 | 0,020 | 0,30 | 0,08 | 0,30 | – |
| Al tot min. | Cu max | Nb max. | Ti max. | V max. | Cr+Cu+Mo+Ni max. |
| – | 0,30 | 0,010 | 0,04 | 0,02 | 0,70 |
Mechanical properties of EN 10216-1 P265
Mechanical properties for quality TR2
| Steel grade | Tensile properties | Impact properties | ||||||||
| Steel name | Steel number | Upper yield strength R eH b min. for Wall Thickness T mm | Tensile Strength R m | Elongation A min. % | Minimum average absorbed energy KV 2 J at a temperature of °C | |||||
| T ≤ 16 | 16 < T ≤ 40 | 40 < T ≤ 60 | l | t | ||||||
| MPa * | MPa * | MPa * | MPa * | l | t | 0 | -10 | 0 | ||
| P265TR2 | 1.0259 | 265 | 255 | 245 | 410 to 570 | 21 | 19 | 40 | 28 d | 27 |
Note: l = longitudinal t = transverse
Mechanical properties for quality TR1
| Steel grade | Tensile properties | Impact properties | ||||||||
| Steel name | Steel number | Upper yield strength R eH b min. for Wall Thickness T mm | Tensile Strength R m | Elongation A min. % b c | Minimum average absorbed energy KV 2 J at a temperature of °C c | |||||
| T ≤ 16 | 16 < T ≤ 40 | 40 < T ≤ 60 | l | t | ||||||
| MPa * | MPa * | MPa * | MPa * | l | t | 0 | -10 | 0 | ||
| P265TR1 | 1.0258 | 265 | 255 | 245 | 410 to 570 | 21 | 19 | – | – | – |
Note: l = longitudinal t = transverse
Tolerances of EN 10216-1 Seamless steel tubes
Tolerances on outside diameter and on wall thickness
| Outside diameter D mm | Tolerances on D | Tolerances on T for a T/D ratio | |||
| ≤ 0,025 | > 0,025 ≤ 0,050 | > 0,050 ≤ 0,10 | > 0,10 | ||
| D ≤ 219,1 | ± 1% or ± 0,5 mm whichever is the greater | ± 12,5 % or ± 0,4 mm whichever is the greater | |||
| D > 219,1 | ± 20 % | ± 15 % | ± 12,5 % | ± 10 % a | |
| a For outside diameters D ≥ 355,6 mm it is permitted to exceed the upper wall thickness locally by a further 5 % of the wall thickness T | |||||
Tolerances on exact lengths
| Length L | Tolerance on exact length |
| L ≤ 6 000 | + 10 0 |
| 6 000 < L ≤ 12 000 | +15 0 |
| L > 12 000 | +by agreement 0 |
Inspection
Types of inspection
non-specific or specific inspection for quality TR1;
specific inspection for quality TR2.
Testings
(1)Chemical analysis
(2)Tensile test
(3)Impact test
(4)Leak tightness test(Hydrostatic test)
(5)Electromagnetic test
(6)Dimensional inspection
(7)Visual examination
(8)Non-Destructive Testing
Marking
The marking shall be indelibly marked on each tube at least at one end. For tubes with outside diameter D ≤ 51 mm the marking on tubes may be replaced by the marking on a label attached to the bundle or box.
Protection
The tubes will be delivered with a temporary protective coating.
